How to Open a Krylon Spray Paint Can

Before opening a Krylon spray paint can, make sure to read the warnings and precautions on the label. To open the can, remove the cap by unscrewing it counterclockwise. Next, puncture the inner seal of the can with the pointy end of the cap.

Finally, screw the cap back on clockwise and shake the can vigorously for about 60 seconds.


  • Open the Krylon spray paint can by unscrewing the cap
  • Place your finger over the opening of the can, and shake it well for a minute or two
  • Aim the can at your desired surface, and depress the nozzle to start spraying

How to Open a Spray Paint Can Without a Screwdriver

Spray paint cans are a great way to add color and personality to any project, but opening them can be a challenge. If you don’t have a screwdriver handy, there are a few other ways to get the job done. One option is to use a can opener.

This tool will puncture the top of the can open, allowing you to access the contents inside. Be sure to wear gloves when using a can opener, as the sharp edges can be dangerous. Another option is to use a hammer and nails.

Simply place two nails into the top of the can (one on each side) and then use the hammer to gently tap them down. This will create two small holes that you can use to pour out the spray paint. Again, be careful with this method as sharp edges may be present.

If all else fails, you can always bring your spray paint can to a local hardware store or home improvement center and they should be able to help you open it up.

How to Open Spray Paint Can With Screwdriver

Spray paint cans are a great way to add color and personality to any project, but they can be tricky to open. The good news is that you don’t need any special tools to open a spray paint can – all you need is a screwdriver! Here’s how to do it:

  • Start by removing the cap from the spray paint can. You can do this by unscrewing it, or simply prying it off with a screwdriver.
  • Once the cap is off, take your screwdriver and insert it into the small hole in the center of the lid.
  • Turn the screwdriver clockwise until you hear a clicking sound. This indicates that the locking mechanism has been released and you can now remove the lid.
  • Carefully peel back the lid, being careful not to touch the paint inside. And that’s it!

How to Open Rustoleum Spray Paint Can With a Screwdriver

If your Rustoleum spray paint can is giving you trouble opening it with a traditional can opener, don’t despair! There’s an easy workaround using a screwdriver. Simply insert the blade of a screwdriver into the seam between the lid and the can body.

Apply pressure and twist the screwdriver to pry the lid open. It may take a little effort, but eventually, you’ll be able to get the lid off and start painting. If you’re having difficulty getting the screwdriver into position, try using a utility knife or another sharp object to make a small opening in the seam.

This will give you something to grip onto with your screwdriver.

How to Get Paint Out of a Broken Spray Can

When you’re trying to paint a room or piece of furniture, the last thing you want is for your spray can of paint to break. But if it does, don’t worry! There are a few ways to get the paint out and continue with your project.

One way is to pour the paint into another container. This can be tricky, as you don’t want to spill any paint or get it on your clothing. If possible, place the broken can in a sink or other large basin so that you can contain any spills.

Put on some rubber gloves and use a screwdriver or other sharp object to puncture a hole in the bottom of the can. Then, carefully tilt the can and pour the paint into another container. Another way to get paint out of a broken spray can is to use an air compressor.

If you have one available, simply attach the hose to the valve on the bottom of the can and turn on the compressor. The pressure from the air will force the paint out of the can and into whatever container you have placed under it. Just be sure not to point the nozzle directly at yourself or anyone else, as this could cause serious injury!

Finally, if neither of these methods works or if you don’t have an air compressor available, you can always try heating up the slightly with a hairdryer or heat gun set on low. This will help loosen up the paint inside so that it’s easier to pour out.

How to Open Spray Can Nozzle

Assuming you’re talking about a standard aerosol spray can: Before you attempt to open the nozzle, make sure the can is properly positioned – this will help avoid any potential mess. Hold the can upright in your dominant hand, and place your other hand over the top of the can, fingers spread wide.

Apply pressure to the top of the can with your palm whilst simultaneously pressing down on the nozzle with your fingers. The nozzle should pop open easily. If nothing happens when you first try this method, check that there’s no blockage preventing liquid from coming out of the nozzle.

If there is, gently clear it away before trying again.

How to Open a Krylon Spray Paint Can


How Do You Use Krylon Spray Paint?

Krylon spray paint is a versatile product that can be used on a variety of surfaces. To use Krylon spray paint, first, shake the can well and then hold it upright about 10-12 inches from the surface you’re painting. Apply light, even strokes to the surface, moving the can back and forth as you go.

If you’re painting something with a lot of curves or intricate details, you may need to use a smaller brush or even a toothpick to get into all the nooks and crannies. Let your first coat of Krylon dry for about 15 minutes before applying a second coat if necessary.

How Do You Open Krylon Spray Red Cap?

Assuming you are referring to the standard Krylon red spray paint cap: The first thing you need to do is remove the clear plastic protective seal. Once that is off, unscrew the metal ring counterclockwise.

After the ring is removed, you can then pull the red cap off.

How Do You Break Open a Spray Paint Can?

Assuming you’re talking about a standard aerosol spray paint can: The first thing you need to do is remove the cap. To do this, unscrew it counterclockwise until it comes off.

Once the cap is off, there will be a small metal disk with a hole in the center known as the nozzle. The nozzle is what controls the flow of paint and allows you to create different types of lines (thin, thick, etc.). Next, take your index finger and thumb and pinch the sides of the nozzle between them.

This will open up the valve and allow the paint to start flowing out. Now that the paint is flowing, point the can in whatever direction you want to start painting and begin pressing down on the nozzle with your index finger. As you continue to press down, move your hand back and forth across whatever surface you’re painting to get an even coat.

Once you’re finished painting, release pressure on the nozzle and allow any excess paint to drip back into the can. Next, screw on the cap clockwise until it’s tight – this will seal up the can so that no paint can escape. And that’s it!

You’ve now successfully broken open a spray paint can and are ready to start painting!

Why are Spray Paint Cans Locked Up?

Most people don’t know that spray paint cans are locked up for a very good reason. The main ingredient in spray paint is highly flammable, and if it were to get into the wrong hands, it could be used to start fires. In addition, many assignment shops and recycling centers will not accept spray paint cans because of the fire hazard they pose.

So next time you see a sign that says “No Spray Paint Cans Allowed,” remember that it’s for everyone’s safety!


Krylon is a trusted brand when it comes to spray paint, and their cans are no different. In this post, we’ll show you how to open a Krylon spray paint can so you can get started on your project. The first thing you’ll need to do is remove the cap from the can.

To do this, unscrew the cap counterclockwise until it comes off. Once the cap is off, you’ll see a small metal ring around the opening of the can. This ring is called the nozzle, and it’s what controls the flow of paint when you’re spraying.

To start painting, hold the can about 10-12 inches away from your surface and depress the nozzle with your finger. As you depress the nozzle, the paint will come out in a fine mist. Move your hand back and forth as you spray to evenly coat your surface.

When you’re finished painting, release the nozzle and screw the cap back on clockwise until it’s tight.